Pulling wire for a service panel, a sub-panel, or a long run to an outbuilding can go sideways fast when the cable doesn’t match the job. Aluminum feeder and service entrance wires are built for heavier amp draws than the branch wiring inside your walls, and the 4-2 family covers a useful middle ground for mobile home feeders, residential service laterals, and direct-burial runs to detached structures.
I’ve sorted seven options by use case so you can match gauge, insulation type, and listing to the project in front of you. Pay attention to whether a cable is rated for direct burial, whether it includes a neutral, and whether the jacket is suited to wet or dry locations before you commit.
The Shortlist At A Glance
More Details On Our Top Picks
This cable is built for the heavy end of residential feeder work. The 4/0 gauge conductors (a wire thickness roughly equivalent to a thick pencil) are paired with a smaller 2/0 neutral, which is the classic mobile home feeder layout where the unbalanced load between the two hot legs doesn’t demand a full-size neutral. The 600V rating covers typical residential service voltages with headroom to spare.
If you’re feeding a manufactured home from a meter base or replacing an aging feeder, this short 10-foot cut fits the typical mast-to-disconnect span. Compared to the smaller 4-4-4-6 SER cable (Item 3) that works fine for sub-panels, this one handles much heavier amp draws at the cost of more weight per foot. Aluminum construction keeps the overall mass manageable for its gauge class.
Strengths Worth Knowing
- 4/0 gauge supports high ampacity runs to large mobile homes
- Three hot conductors plus a reduced 2/0 neutral saves material cost
- 600V rating exceeds standard residential service voltages
- Short 10-foot length suits tight meter-to-disconnect spans
Trade Offs
- At roughly 1.02 lbs per foot, the cable is heavy and awkward to maneuver alone
- Overkill for small feeder jobs where lighter gauge cable would do
Who It Suits Best
Pros and experienced homeowners wiring a manufactured home service entrance where the panel demands serious ampacity.
Consider Something Else When
The Nassau 25′ 3/0-3/0-3/0-1/0 SER cable suits shoppers needing a mid-sized sub-panel feeder without the 4/0 weight.
SER stands for Service Entrance Rated, a cable classification approved for the run from the meter base to the main panel or sub-panel inside a building. The three 3/0 conductors carry the two hot legs and neutral (or three hots on a three-phase setup), while the reduced 1/0 ground keeps the cable lighter than a fully balanced design. Twenty-five feet covers most detached garage or workshop sub-panel installs without leaving much slack to coil.
For homeowners running power to a shed, this cable lands between the heavy Item 1 mobile home feeder and the lighter 4-4-4-6 SER. You get serious ampacity without paying for the full 4/0 weight. Aluminum SER cable is widely accepted in residential work, though anti-oxidant compound at the termination lugs is a commonly recommended practice for long-term reliability.
Advantages To Know
- 3/0 gauge handles substantial sub-panel loads
- 25-foot length matches typical garage or shed feeds
- Aluminum construction weighs less than equivalent copper
Points To Note
- Not direct burial rated, so outdoor runs need conduit
- Requires properly torqued lugs and anti-oxidant paste at terminations
- Overkill for small 60A sub-panel applications
The Right Fit For
Homeowners feeding a 100A or larger sub-panel to a detached garage or workshop from the main service.
Look Elsewhere When
The Nassau 100′ 4-4-4-6 SER cable makes more sense for whole-shop rewires where the lighter gauge is sufficient.
The 4-4-4-6 configuration is a workhorse for residential service entrance wiring in many homes. Three 4 AWG conductors carry the hot and neutral legs, while the smaller 6 AWG ground handles equipment grounding. At 100 feet, this reel is sized for whole-house service entrance replacements or new construction where the utility feed needs a long interior run to the panel.
Compared to the heavier Item 2 3/0 SER cable, this one trades ampacity for easier handling. Most residential main panels in the 100A to 200A range can be fed with 4 AWG aluminum when the run length is reasonable. You may find the jacket a bit stiff in cold weather, which is normal for SER cable but worth planning around during winter installs.
A Favorable Mix
- 4 AWG aluminum covers typical residential service entrance loads
- 100-foot length accommodates whole-panel rewires
- 6 AWG ground meets standard equipment grounding requirements
Honest Caveats
- Not direct burial rated, so exterior sections need conduit
- Jacket stiffness can complicate tight bends in cold installs
Built With In Mind
Homeowners and electricians replacing a residential service entrance cable where 4 AWG aluminum matches the panel rating.
Not Your Match When
The Wirenco 2-2-2-4 SER 50-foot cut is a better fit for smaller 100A service entrance upgrades with shorter runs.
URD means Underground Residential Distribution, and this cable is rated for direct burial without conduit. The 2-2-4 layout puts two phase conductors at 2 AWG with a reduced 4 AWG neutral, and the cross-linked polyethylene insulation resists moisture, abrasion, and heat in the soil. UL listing adds a third-party check that the cable meets safety standards for buried installations.
Where the Nassau SER cables above need conduit for any underground section, this one goes straight in the trench (typically 24 inches deep for residential feeds). The 7-strand construction, which means each conductor is built from seven smaller strands twisted together, makes pulling through bends easier than solid-core designs. For a 100-foot run to a detached shop or a secondary panel, this is the practical choice.
Good Reasons To Consider
- UL listed for direct burial, so no conduit required in the trench
- 2 AWG phase conductors handle typical outbuilding sub-panel loads
- Cross-linked polyethylene insulation stands up to soil moisture
- 100-foot length covers most residential secondary runs
Worth Noting
- Trench depth and warning tape per local code still apply
- Reduced 4 AWG neutral may limit heavily unbalanced 120V loads
Who Should Grab It
Homeowners running an underground feed to a detached garage, shed, or outbuilding panel.
Swap It Out When
The Nassau 80′ URD quadruplex cable suits longer underground runs that need a full-size neutral for three-phase or balanced loads.
This quadruplex cable, meaning a four-conductor bundle twisted together for distribution use, carries two 2 AWG phase conductors plus a full-size 4 AWG neutral and an additional neutral leg. The 60 mil insulation thickness (a mil is one-thousandth of an inch) and 0.973-inch overall diameter reflect a heavier-duty direct burial construction than lighter residential cables. At 367 lbs per 1000 feet, it’s substantial but not unmanageable for trench pulls.
The ampacity numbers tell the real story: 155 amps in direct burial and 115 amps when run in conduit. For most residential sub-panel feeds to outbuildings, the direct burial rating is what matters, and 155A gives comfortable headroom over a typical 100A sub-panel. Compare this to Item 4’s 165A rating and slightly different construction, and the choice comes down to length needed and whether you want the extra neutral conductor.
Notable Upsides
- 155A direct burial ampacity covers most residential sub-panel loads
- Quadruplex design includes full neutral for balanced loads
- 60 mil insulation thickness adds mechanical protection
Small Caveats
- 80-foot length may fall short for longer property runs
- Heavier than the BreezeHug cable, so trench pulls take more effort
Whose Shelf It Belongs On
Electricians and homeowners wiring an underground secondary distribution run where a full neutral and higher ampacity are required.
Where A Sibling Pick Shines
The BreezeHug 100 Ft 2-2-4 URD cable suits longer runs where the lighter 7-strand construction makes pulling easier.
Rated for 600 volts and 100 amps, this SER cable is sized for the smaller end of residential service entrance upgrades. The 2-2-2-4 layout gives you three 2 AWG conductors plus a 4 AWG neutral, and the wet-and-dry location rating means it works indoors, in damp basements, or in exterior conduit runs where it stays dry. At 0.359 lbs per foot, it’s noticeably lighter than the heavier 4/0 mobile home feeder.
For a 100A service entrance replacement on a small home, or a sub-panel feed to a modest workshop, this cable lands in a sweet spot. The 50-foot cut suits typical short meter-to-panel distances without excessive waste. Compared to Item 4’s underground-rated cable, this one needs conduit if you run it outside, but it’s friendlier to work with indoors.
Why It Works Well
- 100A rating covers small residential service entrances
- Wet and dry location rating adds installation flexibility
- Lighter weight per foot than higher-ampacity SER cables
Points To Keep In Mind
- Not direct burial rated, so underground sections need conduit
- 50-foot cut may be too short for longer service runs
Who Will Love This
Homeowners tackling a 100A service entrance upgrade or short sub-panel feed where lighter cable and a manageable length matter.
Reach For A Different Pick When
The Nassau 100′ 4-4-4-6 SER cable works better for longer runs where 4 AWG aluminum is sufficient for the load.
MC cable (Metal Clad) wraps insulated conductors in an aluminum armor jacket that acts as both physical protection and an equipment grounding path. This 6/3 configuration includes three 6 AWG stranded copper conductors plus a ground, and the 75A ampacity suits branch circuits, feeder runs, and service distribution in commercial or multi-residential settings. The aluminum armor is lighter and more flexible than steel-jacketed alternatives.
This cable occupies a different niche than the SER and URD options above: it’s for exposed indoor runs, commercial feeders, and multi-family construction where the armored jacket replaces conduit. Where the Wirenco SER cable (Item 6) handles service entrance duties, this MC cable handles branch and feeder distribution inside the building. The 30-foot cut suits panel-to-panel jumps or short commercial feeder runs.
Where It Delivers
- Aluminum armor provides physical protection without separate conduit
- Stranded copper conductors simplify bending and termination
- Suits branch, feeder, and service distribution in commercial settings
Things To Consider
- Specialized anti-short bushings required at every termination
- 75A rating is lower than the heavier SER cables in this roundup
- Aluminum armor needs correct connectors and proper grounding
Best Suited To
Commercial electricians and multi-residential contractors running exposed indoor feeder or branch circuits where the armored jacket replaces conduit.
A Better Fit Elsewhere
The Nassau 25′ 3/0-3/0-3/0-1/0 SER cable works better for residential sub-panel feeds where higher ampacity matters more than armor.
Choosing the Right Gauge and Cable Type for the Job
The 4-2 family of aluminum wires spans service entrance cable, underground distribution cable, and metal clad feeder cable, and the right pick depends entirely on where the wire is going and how much current it needs to carry. AWG (American Wire Gauge) numbers work counterintuitively: smaller numbers mean thicker wire and higher ampacity, so 2 AWG carries more current than 4 AWG, and 4/0 carries far more than either.
For service entrance work, the cable type matters as much as the gauge. SER cable is rated for the dry, protected run from the meter to the main panel, but it cannot go directly into the ground. URD cable is the opposite: built for direct burial with cross-linked polyethylene insulation that shrugs off soil moisture, but not always listed for indoor use. Mixing them up can fail inspection or, worse, create a long-term reliability problem.
Gauge selection ties to your panel’s amp rating and the run length. A 100A panel typically takes 4 AWG aluminum for short runs or 2 AWG for longer distances to account for voltage drop. A 200A main usually needs 4/0 at the feeder end. Local electrical codes (based on the National Electrical Code) may specify larger wire than the bare minimum, especially for longer runs, so checking with your inspector before buying is always worth the call.
Match Cable to Location First
Direct burial, conduit-only, or exposed indoor: each environment rules out some cable types and demands others. URD cable goes in the trench, SER cable stays inside or in conduit, and MC cable handles exposed indoor runs where you want armor instead of pipe. Starting with the installation environment saves you from returning the wrong reel.
Insulation type matters too. Cross-linked polyethylene (XLPE) handles heat and moisture better than the PVC jackets on older SER cable, which is one reason newer URD products last longer in wet soil. For indoor runs, the standard SER jacket is fine as long as it stays in a protected location.
Calculate Ampacity Against Run Length
The ampacity numbers on the spec sheet assume a baseline installation condition, and longer runs lose more voltage to resistance. Aluminum has higher resistance than copper, so aluminum runs need to be one or two gauges larger than the equivalent copper to deliver the same voltage at the far end of the run.
For runs over 100 feet, the voltage drop calculation often forces you to upsize the cable beyond what the panel rating alone would suggest. Online voltage drop calculators let you plug in your load amperage, run length, and target voltage to find the right gauge for your specific situation.
Don’t Skip the Terminations
Aluminum cable needs antioxidant compound at the lugs and properly rated terminations to prevent oxidation at the connection points. The lugs on your panel or sub-panel should be dual-rated for aluminum and copper conductors, and the torque specification on each lug matters for long-term reliability.
Skipping the antioxidant paste is one of the most common causes of aluminum feeder failures years after installation. The paste is cheap, the application takes seconds per termination, and it prevents the slow corrosion that builds resistance and heat at the connection.
Slip Ups and Smart Upgrades in Aluminum Feeder Cable
Wrong Turns To Avoid
The most common mistake is grabbing SER cable for an underground run because it was cheaper or more available. SER is not direct burial rated, and burying it without conduit is an inspection failure waiting to happen. Conversely, running URD cable exposed indoors where the jacket isn’t designed for that environment can create code issues and premature jacket degradation.
Another trap is undersizing the neutral. A 4-2 cable with a reduced neutral works fine for typical residential loads, but if you’re running heavy 120V equipment like welders or EV chargers on one leg, the unbalanced current can push the smaller neutral beyond its rating. When in doubt, a full-size neutral costs more upfront but prevents headaches later.
What The Higher Tier Buys
Spending more in this category usually gets you heavier gauge, longer length, or better insulation. A 4/0 mobile home feeder costs more than a 2-2-2-4 SER because it carries roughly three times the ampacity. The upgrade is worth it when your panel and loads actually need that capacity, but it’s wasted money if you’re feeding a 100A sub-panel.
The insulation upgrade from standard PVC to cross-linked polyethylene shows up in URD cable ratings, and it pays off in direct burial longevity. MC cable commands a premium over SER for the aluminum armor jacket, and that premium is justified in exposed indoor runs where the armor replaces separate conduit work.
Frequently Asked Questions
What’s the difference between SER and URD cable?
SER (Service Entrance Rated) cable is designed for above-ground service runs from the meter to the main panel, while URD (Underground Residential Distribution) cable is built for direct burial in trenches without conduit.
Can I use aluminum cable for a 100A sub-panel?
Yes, 2 AWG aluminum is a common size for 100A sub-panel feeders at typical run lengths, though longer distances may require upsizing to account for voltage drop.
Do I need conduit for SER cable?
SER cable can be run exposed indoors in protected locations, but any outdoor or underground section requires approved conduit to shield it from physical damage and moisture.
Why do some cables have a smaller neutral than the hot conductors?
A reduced neutral saves material cost because residential 120/240V services rarely draw equally on both hot legs, so the neutral carries less current than either hot conductor in most installations.
Is MC cable the same as armored cable?
MC (Metal Clad) cable is a type of armored cable with a metal jacket surrounding the conductors, where the armor can serve as the equipment grounding path when properly bonded.
The Takeaway
Matching the cable type to the installation environment matters more than chasing the heaviest gauge. Direct burial URD, service entrance SER, and metal clad MC each have a defined role, and picking the right one for your project avoids inspection problems and long-term reliability issues. Confirm your panel amp rating, calculate voltage drop for the actual run length, and don’t skip the antioxidant compound at the lugs.






