Picking the right aluminum feeder cable gets confusing fast, especially when the labels all start looking the same. I spend a lot of time helping homeowners and contractors sort through gauge numbers, conductor counts, and burial ratings, and the honest truth is that the wrong wire choice can turn a Saturday project into a Sunday headache. This shortlist covers six 4 4 aluminum wires that handle very different jobs, from mobile home feeds to direct-burial runs, so the right match stays close at hand.
A Side-By-Side Look
The Strengths Of Each Pick
Mobile home feeders demand heavier gauge than typical residential runs, and this Nassau 10-foot length delivers exactly that. The 4/0-4/0-4/0-2/0 configuration means three insulated phase conductors plus a reduced neutral, which is the classic mobile home setup electricians reach for.
At 1.02 lbs per foot, this is genuinely hefty cable, so plan a helper for the pull. For anyone setting up a manufactured home or replacing a tired feeder, the 600V rating covers standard residential service without a second thought.
Bright Spots
- 4/0 gauge handles the high-amperage needs of mobile home service panels
- Three conductors with a 2/0 neutral match common manufactured home hookups
- 600V rating gives flexibility for both 200A and 100A service work
- Short 10-foot length reduces waste on tight service masts
Trade Offs
- Only 10 feet may fall short for longer yard runs or setback installations
- 4/0 aluminum is stiff and heavy, so routing through conduit takes patience
Feature Snapshot
Right Fit For
Contractors and homeowners wiring a manufactured or mobile home with a short feeder run from the meter base to the home’s service panel.
Swap It Out When
The run needs more than 10 feet, in which case the Nassau 80′ URD Dyke direct burial cable handles longer underground pulls more economically.
SER cable (Service Entrance Rated cable, designed to run from the utility meter to the main breaker panel) is the workhorse of residential service work, and this Nassau 25-foot length steps down from the heavier 4/0 mobile home feeder with sensible 3/0 conductors. The 3/0-3/0-3/0-1/0 build suits typical 200A main panel replacements where a slightly lighter cable is welcome.
For installers running service entrance cable through attic spaces or down exterior walls, the shorter conductor count and standard 600V rating keep this within NEC (National Electrical Code) residential practice. Compared to the heavy 4/0 cable reviewed above, this one trades raw amperage capacity for easier handling on a ladder.
Standout Benefits
- 3/0 conductors handle standard residential 200A service panel work
- Three conductors with ground cover the typical single-phase hookup
- 25-foot length gives flexibility for mast-to-panel runs on most homes
Points To Keep In Mind
- SER cable is rated for above-ground use only, never direct burial
- Aluminum conductors require antioxidant compound at termination points
- Heavier than copper equivalents, so ceiling joist routing needs proper staples
Built With In Mind
Licensed electricians and experienced homeowners replacing or upgrading a residential main service panel with a clean 25-foot run.
A Better Fit Elsewhere
The Copkim 4-4-4-6 SER cable suits smaller sub panel feeders in detached garages or workshops where 3/0 gauge is overkill.
Sub panel feeders for garages and shops demand less amperage than full service entrances, which is where 4-4-4-6 SER cable earns its keep. Copkim’s 25-foot run delivers 4 AWG phase conductors with a 6 AWG neutral, well matched to 60A or 100A sub panel installations.
The aluminum construction keeps the weight manageable for a single-person pull, and the jacket strips and cuts cleanly for those tackling weekend projects. Where the heavier Nassau 3/0 cable reviewed above targets main panel work, this Copkim option sits in the sweet spot for detached structures.
A Few Highlights
- 4 AWG conductors with 6 AWG neutral fit standard sub panel feeders
- Lighter weight than higher-gauge SER cable, easier solo handling
- 25 feet covers most garage and shop sub panel runs without excess
- 600V rating supports typical residential distribution work
Worth Noting
- Not rated for direct burial, so underground runs to a detached shop need conduit or a different cable
- Smaller gauge means this cannot replace a main service entrance cable for whole-home use
Quick Facts
Perfect Match For
Homeowners running power to a detached garage, workshop, or shed sub panel from the main house panel above ground.
Look Elsewhere When
The run needs to go underground, where the Nassau 80′ URD Dyke direct burial cable is purpose-built for trench installs.
Direct burial cable opens up jobs that would be impossibly expensive with conduit, and this Nassau 80-foot URD (Underground Residential Distribution) Dyke run is built for exactly that. The 2-2-2-4 quadruplex setup handles typical 100A underground service drops to outbuildings, well pumps, or detached workshops.
Owners commonly appreciate that the polyethylene jacket stands up to soil contact and moisture without needing additional conduit. For long yard runs where trenching is the only realistic option, this cable does what the above-ground Copkim 4-4-4-6 SER simply cannot.
Features That Help
- Direct burial rated, so no conduit required for trench installs
- 80-foot length handles most residential yard-to-outbuilding runs
- 155A ampacity in direct burial covers 100A sub panel service with margin
Honest Caveats
- Heavier than SER cable at 367 lbs per 1000ft, so spool handling needs care
- Direct burial only, not approved for interior wiring inside buildings
- Requires proper trench depth per local code, typically 24 inches
Key Product Details
Whose Shelf It Belongs On
Property owners and electricians trenching underground service to detached shops, barns, or well pumps that need a true 100A feed.
Not Your Match When
The job is a simple above-ground sub panel inside an attached garage, where the Copkim 4-4-4-6 SER cable is easier to work with.
Not every wiring job is about feeding a house. This Cablectric 14 gauge primary wire assortment targets automotive and low voltage work where four colors help keep circuits organized. The PVC insulation resists abrasion, sunlight, and chemical exposure, all common enemies under the hood or in a trailer.
Where the heavy service entrance cables reviewed earlier run hundreds of amps to a panel, this 14 gauge wire handles remote starts, trailer harnesses, and accessory circuits without breaking a sweat. For hobbyists and gearheads, having four rolls in different colors cuts the project time noticeably.
Notable Gains
- Four assorted colors keep positive, negative, accessory, and signal circuits organized
- 14 gauge handles typical automotive accessory and lighting loads
- Flexible PVC insulation bends easily through tight engine bay routes
Small Caveats
- 14 gauge is too light for any household 120V/240V service work
- Color assortment specifics may not match every project plan, so verify before ordering
Made For
Car enthusiasts, trailer owners, and DIYers wiring automotive accessories, remote starters, or low voltage landscape lighting.
Consider Something Else When
The goal is feeding a sub panel or main service, where the Wirenco 2-2-2-4 SER cable handles 100A residential service properly.
When 100A service is the target and the run is above ground, 2-2-2-4 SER cable hits the mark without overspending on heavier gauge. This Wirenco 50-foot cut offers four wires total, three conductors plus a bare neutral, and the 600V rating covers standard residential distribution needs.
Rated for both wet and dry locations, this cable handles outdoor service masts and damp basements with the same confidence. At 0.359 lbs per foot, it lands between the heavier Nassau 3/0 SER and the lighter Copkim 4-4-4-6, which makes it a flexible middle option.
The Helpful Details
- 2 AWG conductors rated for 100A service at 600V
- Wet and dry location rated, so outdoor masts and damp spaces both qualify
- 50-foot length covers typical house-to-detached structure runs
Practical Considerations
- 50-foot cut may leave leftover material on shorter projects
- Above-ground only, so burial routes require a different cable type
Best Suited To
Homeowners and contractors installing a 100A main or sub panel above ground with a moderate-length run between buildings.
Reach For A Different Pick When
The path goes underground, where the Nassau 80′ URD Dyke direct burial cable saves the cost and labor of conduit.
What Matters Most Before Choosing 4 4 Aluminum Wires
Conductor Gauge And Amperage
Cable gauge controls how much current the wire can safely carry, and aluminum wire of the same gauge typically handles about 84% of the current that copper would at the same size. For typical 100A sub panel feeders, 2 AWG or 4 AWG aluminum works well, while 200A main services often step up to 3/0 or 4/0. Mobile homes and larger manufactured structures usually push into 4/0 territory for their primary feed. Picking a gauge below the load requirement is the most common mistake, and it shows up as nuisance breaker trips or, worse, overheated insulation.
Cable Type And Installation Environment
SER cable works for above-ground runs through attics, walls, and exterior surfaces, while URD cable handles direct burial without conduit. Mixing the two is a code violation, so the trench or surface path matters before choosing a cable. Cable labeled for wet and dry locations offers the most flexibility for outdoor service masts and damp basements. Picking the wrong jacket rating for the environment is one of the fastest ways to fail inspection.
Conductor Count And Neutral Sizing
The four-number naming convention like 4-4-4-6 tells the full story: three conductors of the first size, plus a reduced neutral of the second. A 2-2-2-4 quadruplex handles 100A residential service, while 3/0-3/0-3/0-1/0 supports heavier 200A runs. Verifying the neutral size matches the calculated load prevents voltage drop on long feeders. For sub panels feeding 240V equipment like welders or EV chargers, the conductor count must match the breaker configuration.
Length, Weight, And Handling
Aluminum cable weighs noticeably less than copper but still adds up fast on long runs. A 50-foot cut of 2-2-2-4 SER lands around 18 lbs, while 80 feet of 2-2-2-4 URD pushes closer to 30 lbs once the heavier burial jacket enters the picture. Pulling heavier gauge through tight bends gets physically demanding, so realistic handling matters as much as electrical specs.
Key Considerations Across These Picks
Pitfalls Shoppers Hit
The most common slip is grabbing SER cable for an underground run, which violates code and fails inspection every time. Another trap is underestimating the gauge requirement, picking 4 AWG when the panel demands 2/0 or 3/0 for a 200A service. Some shoppers also overlook the neutral size, only to discover voltage drop on long feeders to detached shops.
When Paying More Pays Off
Higher-tier cables typically deliver thicker insulation, longer continuous lengths without splices, and heavier jacket construction that survives rougher installs. For a one-time burial job, spending up on quality URD cable pays back in reliability and inspection success. For automotive work, premium PVC insulation that resists heat and chemical exposure outlasts bargain wire that cracks after one hot summer.
Frequently Asked Questions
What does the 4 4 aluminum wire designation mean?
The 4-4-4-6 designation describes three 4 AWG conductors with a reduced 6 AWG neutral inside a SER-style jacket. It is a common configuration for sub panel feeders in detached garages and shops.
Can I use 4 4 aluminum wire for a main service panel?
For a 100A main service, 4-4-4-6 SER cable works in light-duty applications, though many electricians prefer 2-2-2-4 for added margin. For 200A main services, stepping up to 3/0 or 4/0 SER or URD cable is the standard practice.
Is aluminum wire safe for residential use today?
Modern aluminum alloys with proper antioxidant compound at terminations perform reliably when installed to current NEC standards. The legacy issues from the 1960s and 1970s largely came from incorrect alloy choices and missing anti-oxidant, both of which are addressed in contemporary installations.
How deep must URD cable be buried?
Most local codes call for 24 inches of cover for direct burial URD cable in residential applications. Sandy or rocky soil may require additional depth or a sand bedding layer, so checking with the local inspector before trenching saves rework.
Can SER cable be used outdoors?
SER cable rated for wet and dry locations handles exterior service masts and damp basements without issue. The key is matching the jacket rating to the environment, since not all SER carries both wet and dry approvals.
Wrap Up
Six cables, six jobs, and the right one depends on where the wire needs to run and how much current it must carry. Heavy feeders belong with the Nassau 4/0 mobile home cable, while sub panel work pairs naturally with Copkim 4-4-4-6 SER. Underground runs call for URD, automotive work needs primary wire, and a 100A service above ground fits the Wirenco 2-2-2-4 cleanly. Match the cable to the project, and the rest tends to fall into place.






